| Inverter Part |
| Supply voltage (VPN) | Applied between P - NU,NV,NW | 0 | - | 450 | V |
| Supply voltage (surge) (VPN(surge)) | Applied between P - NU,NV,NW | - | - | 500 | V |
| Collector-emitter voltage (VCES) | | - | - | 600 | V |
| Output phase current (IC) | TC=25C, TJ<150C | - | - | 10 | A |
| Output phase current (IC) | TC=100C, TJ<150C | - | - | 5 | A |
| Output peak phase current (IPK) | TC=25C, less than 1ms pulse width | - | - | 20 | A |
| Short circuit withstand time (tSC) | VPN400V, TJ=150C, VD=15V (Note 1) | - | - | 5 | s |
| Collector dissipation (PC) | TC=25C, per 1 chip | - | - | 23 | W |
| Operating junction temperature (TJ) | | -40 | - | +150 | C |
| Control (Protection) Part |
| Control supply voltage (VD) | Applied between VD(H)-COM, VD(L)-COM | 13.5 | 15.0 | 16.5 | V |
| High-side control bias voltage (VDB) | Applied between VB(U)-U, VB(V)-V, VB(W)-W | 13.5 | 15.0 | 18.5 | V |
| Input voltage (VIN) | Applied between IN(UH), IN(VH), IN(WH), IN(UL), IN(VL), IN(WL) - COM | VD0.5 | - | VD0.5 | V |
| Fault output supply voltage (VFO) | Applied between VFO - COM | VD0.5 | - | VD0.5 | V |
| Fault output current (IFO) | Sink current at VFO terminal | - | - | 1 | mA |
| Current sensing input voltage (VSC) | Applied between CSC - COM | 50.5 | - | - | V |
| Temperature output (VOT) | Applied between VOT - COM | 50.5 | - | - | V |
| Total System |
| Self protection supply voltage limit (VPN(PROT)) | VD=13.5-16.5V, Inverter part TJ=150C, Non-repetitive, less than 2s | - | - | 400 | V |
| Module case operation temperature (TC) | Measurement point of TC is provided in Figure 1 | -30 | - | +125 | C |
| Storage temperature (TSTG) | | -40 | - | +150 | C |
| Isolation voltage (VISO) | 60Hz, sinusoidal, AC 1min, between connected all pins and heat sink plate | - | 2000 | - | Vrms |
| Thermal Resistance |
| Junction to case thermal resistance (Rth(j-c)Q) | Inverter IGBT part (per 1/6 module) (Note 2) | - | - | 5.4 | K/W |
| Junction to case thermal resistance (Rth(j-c)F) | Inverter FWD part (per 1/6 module) (Note 2) | - | - | 6.9 | K/W |
| Electrical Characteristics |
| Collector-emitter saturation voltage (VCE(SAT)) | VD=VDB=15V, VIN=5V, IC=5A, TJ=25C | - | 1.60 | 2.00 | V |
| Collector-emitter saturation voltage (VCE(SAT)) | VD=VDB=15V, VIN=5V, IC=5A, TJ=125C | - | 1.90 | - | V |
| FWD forward voltage (VF) | VIN=0, IF=5A, TJ=25C | - | 1.48 | 1.90 | V |
| Switching times (tON) | VPN=300V, VD=VDB=15V, IC=5A, TJ=25C, VIN=0V 5V, Inductive load (high-side) | 0.30 | - | 1.10 | s |
| Switching times (tOFF) | VPN=300V, VD=VDB=15V, IC=5A, TJ=25C, VIN=0V 5V, Inductive load (high-side) | 1.00 | - | 1.50 | s |
| Collector-emitter leakage current (ICES) | VCE=VCES, TJ=25C | - | - | 1 | mA |
| Collector-emitter leakage current (ICES) | VCE=VCES, TJ=125C | - | - | 10 | mA |
| Quiescent VD supply current (IQDH) | VD(H)=15V, IN(UH, VH, WH)=0V, VD(H) - COM | - | - | 0.1 | mA |
| Quiescent VD supply current (IQDL) | VD(L)=15V, IN(UL, VL, WL)=0V, VD(L) - COM | - | - | 2.1 | mA |
| Quiescent VDB supply current (IQDB) | VDB=15V, IN(UH, VH, WH)=0V, VB(U)-U, VB(V)- V, VB(W)- W | - | - | 0.3 | mA |
| Short-circuit trip level (VSC(ref)) | VD=15V (Note 3) | 0.455 | 0.480 | 0.505 | V |
| Under-voltage protection Trip level (UVDT) | Supply circuit | 9.0 | 10.0 | 11.0 | V |
| Under-voltage protection Reset level (UVDR) | Supply circuit | 10.0 | 11.0 | 12.0 | V |
| Under-voltage protection Trip level (UVDBT) | High-side | 8.5 | 9.5 | 10.5 | V |
| Under-voltage protection Reset level (UVDBR) | High-side | 9.5 | 10.5 | 11.5 | V |
| Temperature output (VOT) | LVIC temperature=90C, Pull down R=10k (Note 4) | 2.74 | 2.92 | 3.10 | V |
| Temperature output (VOT) | LVIC temperature=25C, Pull down R=10k (Note 4) | 1.06 | 1.25 | 1.43 | V |
| Over-temperature protection (OTT) | VD=15V, detect LVIC temperature (Note 5) | 100 | 120 | 140 | C |
| Hysteresis of trip reset (OTHYS) | | - | 10 | - | C |
| Fault output voltage (VFOH) | VSC=0V, VFO circuit: 10k to 5V pull-up | 4.9 | - | - | V |
| Fault output voltage (VFOL) | VSC=1V, VFO circuit: 10k to 5V pull-up | - | - | 0.5 | V |
| Fault output pulse width (tFO) | (Note 6) | 20 | - | - | s |
| Input current (IIN) | VIN=5V | - | 1.0 | - | mA |
| ON threshold voltage (Vth(on)) | Applied between IN(...) COM | 2.3 | 2.6 | - | V |
| OFF threshold voltage (Vth(off)) | Applied between IN(...) COM | 0.8 | - | 1.2 | V |
| ON/OFF threshold hysteresis voltage (Vth(hys)) | Applied between IN(...) COM | - | 1.1 | - | V |
| Bootstrap diode forward voltage (VF(BSD)) | IF=10mA including voltage drop by limiting resistor (Note 7) | 1.0 | - | 2.0 | V |
| Built-in limiting resistance (RBSD) | Included in bootstrap diode | 80 | 100 | 120 | |
| Recommended Operation Conditions |
| Supply voltage (VPN) | Applied between P-NU, NV, NW | 0 | - | 400 | V |
| Control supply voltage (VD) | Applied between VD(H) COM, VD(L) - COM | 13.5 | 15.0 | 16.5 | V |
| High-side bias voltage (VDB) | Applied between VB(U)-U, VB(V)-V, VB(W)-W | 13.5 | 15.0 | 18.5 | V |
| Control supply variation (dVD/dt, dVDB/dt) | | -1 | - | 1 | V/s |
| Arm shoot-through blocking time (tdead) | For each input signal | 1.0 | - | - | s |
| PWM input frequency (fPWM) | -40C < TJ < 150C | - | - | 20 | kHz |
| Minimum input pulse width (PWIN(ON)) | (Note 9) | 0.4 | - | - | s |
| Minimum input pulse width (PWIN(OFF)) | (Note 9) | 0.4 | - | - | s |
| COM variation | Between COM - NU, NV, NW (including surge) | -5.0 | - | +5.0 | V |
| Mechanical Characteristics |
| Mounting torque | Mounting screw: M3 (Note 8) | 0.59 | 0.69 | 0.78 | N m |
| Weight | | - | 5.25 | - | g |
| Flatness | Refer to Figure 5 | -50 | - | 100 | m |
| Package Dimensions (IPM-5) |
| Dimension A | | 8.30 | 8.70 | 9.10 | mm |
| Dimension D | | 33.10 | 33.40 | 33.70 | mm |
| Dimension E | | 18.20 | 18.60 | 19.00 | mm |
| Package Dimensions (IPM-5A) |
| Dimension A | | 8.30 | 8.70 | 9.10 | mm |
| Dimension D | | 33.10 | 33.40 | 33.70 | mm |
| Dimension E | | 18.20 | 18.60 | 19.00 | mm |
